Slyther talk , 19 October UTC. Jilo talk , 24 October UTC. Monty talk , 9 December UTC. Jesself talk , 8 January UTC. Category : Drop rates. The information in this article is based on experimental research conducted by the community, and may contain inaccuracies and speculation. Quantity Material Buy price Subtotal per 1, 0.
Vial of Powerful Blood. Ancient Bone. Elaborate Totem. Pile of Crystalline Dust. Armored Scale. Powerful Venom Sac. Vicious Fang. Vicious Claw. Karka Shell. Pristine Toxic Spore Sample. Glob of Ectoplasm. Pile of Putrid Essence. Charged Lodestone. Molten Lodestone. Crystal Lodestone. Destroyer Lodestone. Glacial Lodestone. Onyx Lodestone. Mounting Dimensions and Spacing Requirements Purpose of the PDP Diagnostic Indicators Network Connector Setting the Node Address Switches Power Wiring Adapter Input Status Word Mapping Data into the Image Table Connection Status Word Definition Connection Enable Word Definition The DP Physical Layer T-junction Connectors Termination Blocks Bus Connector Connect the Adapter to the Network Terminate the Network Entering User Parameter Data User Parameter Data Auto Configure Format Condensed Format Read Configuration Response Data What this Chapter Contains Troubleshooting with the Indicators Product Specifications Device Data Base File How to Contact Us: Sales and Support All Product Returns Procedures for Return of Units Under Warranty Procedures for Return of Units Out of Warranty Un-repairable Units Purchasing Warranty Extension Time Limit for Bringing Suit No Other Warranties Intellectual Property Allocation of risks Controlling Law and Severability To order these publications, contact your local Rockwell Automation representative.
It has been designed and tested to meet the following directives. The adapter and terminal base easily snap on the DIN rail by hand. Refer to the installation instructions shipped with these components.
Screw holes are also provided to horizontally or vertically panel-mount your system in an enclosure. Use the optional CE1 0. Do not use more than one cable per system. Diagnostic indicators are located on the front panel of the adapter module. The indicators are:. Upon power-up, the adapter goes to an initialization state and performs a selftest memory check, data memory clear. The indicators also go through a selftest sequence.
If a failure occurs, the adapter transitions to a faulted state and waits for reset cycle power. Otherwise, the adapter begins monitoring the network run state for messages.
Chapter 5 describes the diagnostic indicators and how to use them for troubleshooting. Set the node address using the 2-position thumbwheel switch. Valid settings range from 01 to Connections are provided for connecting the required 24V dc power to the front of the module. The power wiring can be daisy-chained to the terminal base unit located next to the adapter to supply power to the module installed in that base unit.
Refer to the Installation Instructions pub. Read words consist of input and status words, and write words consist of output and configuration words. The number of read words or write words can be 0 or more.
Status and configuration are optional, depending on the module. For example, a 16 point discrete input module will have up to 2 read words and 1 write word. The first word of output data sent by the adapter is the Adapter Status Word. The Output data for Slot 1 is received first, followed by the Output data for Slot 2, and so on up to slot 8.
All bits in the output status word are reserved. The first word of input data sent by the adapter is the Adapter Status Word. The Input data from Slot 1 is first after the status word, followed by Input data from Slot 2, and so on up to slot 8.
The adapter input status word bit descriptions are shown in the following table. The node address changed bit is set when the node address switch setting has been changed since power up. The new node address does not take affect until the adapter has been powered down and then powered back up. Until this power cycling occurs, the node address switches will not match the actual node address. Presently, these consist of:. The following topics show typical examples from Rockwell Automation product literature.
Individual channels revert to 4 to 20mA if bit selection is all zeroes. Not used on voltage outputs. Underrange bits U for individual channels 4 to 20mA current inputs only — Bit Wire Off bits W — Current outputs only — When set 1 , the wire on the current.
Bit 00 corresponds to channel 0,. How can we be like Mordecai and Esther? Invite the children to think of situations they face in which it might be hard to do the right thing. Why is it better to do the right thing, even if there are difficult consequences? Discuss how Jesus Christ is an example of this principle. During a time of need, Esther and the Jews fasted. How can you help the children you teach understand the spiritual blessings of fasting?
Then ask them to read Esther —3, 10—17 to find out why the Jews and Esther fasted. Encourage the children to think of a reason they might need special help from the Lord, and suggest they make that reason part of their fast during the next fast Sunday. Invite the children to pretend they are explaining to a friend why they fast. What would they say? Invite the children to share experiences they have had with fasting. Invite the children to sing the song with their families.
Live what you teach.
0コメント