The total ratings of all equipment plugged into the outlet should not exceed 13 amperes. These are clearly labelled. Do NOT touch them. Opening a cover may expose you to shocks or other hazards. If anything happens that indicates that the printer is not working properly or has been damaged, disconnect the printer from the power source and contact your dealer.
These are some of the things to look for:. When replacing a toner cartridge or image unit, reuse the packaging to dispose of the old toner cartridge or image drum unit. Never expose the green drum inside the image drum unit to direct sunlight. Never touch the green drum inside the image drum unit. Do not let it touch your clothing or porous materials. The toner powder causes permanent stains. Using heated water will make removing the stain much more difficult. Never attempt to induce vomiting or give anything by mouth to a person who is unconscious.
Seek medical attention. All button functions on the control panel are now active. These allow the user to access, view and change printer settings. Quick menus are also available from the panel to allow rapid access to more frequently used functions. To access the primary function on a button, press momentarily and release.
To gain access to the secondary function, press and hold the button for at least two seconds. An asterisk. When printer is on-line:. When in menu mode:. It is possible, using the front panel buttons, to change the default configuration of the printer to accommodate software application, specific paper size, method of paper feed and interface connection. The menu structure consists of three levels:. Note: If software can control a feature that is also controlled in the printer menu, the software overrides the menu setting.
Use software to control printer features whenever possible. The LCD shows the item in the top line and the current parameter in the bottom line. The following tables list printer menu selections. Factory default settings are indicated in bold type. Selects emulation. Auto is standard. Page 50 6 Fusing When the transfer is completed, the toner image is fused to the paper by heat and pressure as the paper with unfused toner image passes between the heater roller and the back-up roller.
The heater roller with Teflon coating incorporates a W heater Halogen lamp , which generates heat. Page 51 7 Cleaning When the transfer is completed, the residual toner left on the image drum is attracted to the cleaning roller temporarily by static electricity, and the image drum surface is cleaned.
Page 52 Changes in bias voltage applied to each roller move the attaching toner off the roller to the image drum and return it to the developer. When any of the following conditions arises, this function interrupts the printing process.
Page 57 6. The stirring bar rotation is driven by the link to the protrusion in the stirring gear. Page 60 Operation during Toner Low state When the stirring bar reaches the maximum height, it falls to the minimum height due to its own weight, since there is no resistance provided by the toner on the other side.
Because of this, the time interval during which it is in encounter with the magnet of the sensor lever becomes longer. By monitoring this time interval, Toner Low can be detected. Page 61 The toner sensor is not monitored while the drum motor is in halt.
Only the disassembly procedures are explained here. For reassembly, reverse the steps of disassembly procedure. Page 63 4 Use specified service tools. Parts may be damaged if these sequences are not followed. Note: You can remove the operator panel assy while the upper cover installed on the unit. Remove both the shield plate 3 and face up stacker 4 together.
Note: At the time of mounting, verify the proper the engagements as shown in the diagram. Do not change its default value. Page BPX for any updates to this material. Page Maintenance Image drum cartridge Type About 20, sheets of paper Consumables have been printed. See 1. Page 2 Throw the cleaner pad away. Take proper corrective action as directed by messages which are being displayed on the LCD. Page nn An error was Replace the main control board.
An error was Replace the main control board. Page error. A failure occurred See Section 6. A toner sensor fault - Check the installation of image has occurred when Page continued Defect in the cable - Repair or replace the defective front of the front feeder feeder paper sensor cable and 2-pin paper sensor and connector on the main control board the 2-pin connector or reconnect the connectors.
Jam errors A jam occurred during - Open the cover, remove the paper, paper feeding after then close the cover. When the completion of paper cover is closed, recovery printing is hopping from the tray. Page Size error Manual loading of paper Load the requested paper in the tray. Page data in the on-line mode. Ready flashing: The printer is receiving data or in printing process.
Page Daily status The demo page is being Normal operation. Ready LED blinking: Executed by key operation. Daily status When the number of Normal operation. Page the printer is changed from set mode to another mode.
Daily status Toner is running out. This Replace the toner cartridge. Normal operation can be continued. Figure below shows typical abnormal images. Printer oki okipage 10e setup manual 20 pages printer oki okipage 10e spare parts list. Oki okipage 10e have 9 pdf manuals in 5 languages mainly including setup guide user guide users guide. Blaupunkt service manual user manual daewoo service manual user manual.
Oki 10e user manual 46 pages. Page 14ex printer pdf manual download. View and download okidata okipage 10ex user manual online. Oki okipage 8w lite manual user guide is a pdf file to discuss ways manuals for the oki okipage 8w litein this document are contains instructions and explanations on everything from setting up the device for the first time for users who still didnt understand about basic function of the camera.
November 30, Kip scanner Kip Parts By Kristel. Uniden Phone Instructions Manual. Please refer to the user guide for the types of pa make sure the printer is disconnected from the power sup per to use in this printer.
Kyocera Rave Manual Ebook. Polycom Hdx Integrator Guide Ebook. Post a Comment. December 01,
0コメント